Course Content
TX600 – Service Manual
0/41
Introduction (1.0)
00:00
Safety Precautions (2.0)
00:00
Servicing (3.0)
00:00
Inspection Guide (3.1)
00:00
Program Mode Instructions (3.2)
00:00
Lift Tape Condition (3.3)
00:00
Troubleshooting – Hoist Safety Mechanisms (3.4)
00:00
Testing – Hoist Procedure (4.0)
00:00
Testing the Charger (4.1)
00:00
Battery testing (4.2)
00:00
Tools, Equipment and Lubricants Required for Servicing (5.0)
00:00
Decommissioning (6.0)
00:00
Hoist Removal (6.1)
00:00
Hoist Dismantling (6.2)
00:00
Hoist Disposal (6.3)
00:00
Spare Parts List (7.0)
00:00
Troubleshooting (8.0)
00:00
Servicing – Removal and Replacement (9.0)
00:00
External Covers (9.1)
00:00
PCB (9.2)
00:00
Batteries (9.3)
00:00
Traverse Motor – Powered Traverse Hoist Only (9.4)
00:00
Lift Motor (9.5)
00:00
QRS Hook (9.6)
00:00
Bottom Cover (9.7)
00:00
Limit Switch (9.8)
00:00
Hub (9.9)
00:00
Lift Tape (9.10)
00:00
Wheels – Standard (9.11.1)
00:00
Wheels – QRT System (9.11.2)
00:00
Charging Beak – Standard -Track Type 1 (9.12.1)
00:00
Charging Beak – Track Type 2, 3, 4, 5 and Powered Auxiliary (9.12.2)
00:00
QRT System Charging Beak (9.12.3)
00:00
Constant Charge (9.12.4)
00:00
Battery Lead Fuse (9.13)
00:00
Traverse Shaft and Idle Gear – Powered Models Only (9.14)
00:00
Air Grommet (9.15)
00:00
Toggle switch (9.16)
00:00
E-Lower cord (9.17)
00:00
Traverse Idle Gear (9.18)
00:00
Communications Port (9.19)
00:00
TX600 – Training Manual
0/1
TX600 Advanced - Training Manual
01:01:00
TX600 – Commissioning Manual
0/35
Introduction (1.0)
00:00
Safety Precautions (2.0)
00:00
Required Tools and Equipment (2.1)
00:00
Hoist Unboxing (3.0)
00:00
Hoist Installation (4.0)
00:00
Ceiling Track Access (4.1)
00:00
Installing the Charger (4.2)
00:00
Installing Charging Dock Type 1 – Track Type 1 (4.2.1)
00:00
Installing Charging Dock Type 2 – Track Type 2 (4.2.2)
00:00
Installing Charging Dock Type 3 – Track Type 3, 4 and 5 (4.2.3)
00:00
Installing Charging Dock Type 4 (Track Type 1) – QRT Hoist (4.2.4)
00:00
Installing Charging Dock Type 5 (Track Type 3, 4 and 5) – QRT Hoist (4.2.5)
00:00
Installing the Power Supply to Constant Charge – (Track Type 1) (4.2.6)
00:00
Installing the Power Supply to Constant Charge – (Track Type 2) (4.2.7)
00:00
Installing the Power Supply to Constant Charge – (Track Type 3) (4.2.8)
00:00
Installing the Power Supply to Constant Charge – (Track Type 4) (4.2.9)
00:00
Installing the Power Supply to Constant Charge – (Track Type 5) (4.2.10)
00:00
Installing the Hoist (4.3)
00:00
Installing TX Advanced – Powered Traverse & Return to Charge (RTC) (4.3.1)
00:00
Installing TX Advanced – Constant Charge (Powered Traverse and Manual Traverse) (4.3.2)
00:00
4.3.3 Installing TX Advanced – Powered Auxiliary (Powered Traverse and Manual Traverse) (4.3.3)
00:00
Installing TX Advanced – Quick Release Track (QRT) (4.3.4)
00:00
Component Attachment (5.0)
00:00
Attaching the Handset (5.1)
00:00
Attaching the Carry Bar (5.2)
00:00
Hoist Start Up and Function Checks (6.0)
00:00
Turning the Hoist ON and OFF (6.1)
00:00
Operating Controls (6.2)
00:00
Traversing the Hoist along the Track (6.3)
00:00
Charging the Hoist (6.4)
00:00
Accessories (7.0)
00:00
Decommissioning (8.0)
00:00
Hoist Removal (8.1)
00:00
Hoist Dismantling (8.2)
00:00
Hoist Disposal (8.3)
00:00
TX600 – Spare Parts Manual
The TX600 spare parts manual is a comprehensive guide that provides detailed information about the spare parts used in the TX600 machinery. It includes a parts list, descriptions, illustrations. It is a valuable resource for technicians and maintenance personnel to effectively repair and maintain the TX600 equipment.
0/3
Track Types (1.0)
00:00
Spare Parts Summary (2.0)
00:00
Part Code Detail (3.0)
00:00
Test Topic
TX600 (Fixed Motor)
About Lesson

2.1  Required Tools and Equipment for Hoist Commissioning and Decommissioning

 

When carrying out work on the Ceiling Track Hoist you will require the following:

 

Tools Required

 

2mm T Bar Allen wrench

2.5mm T Bar Allen wrench

3mm T Bar Allen wrench

4mm T Bar Allen wrench

5mm T Bar Allen wrench

5.5mm combination spanner

8mm combination spanner

13mm combination spanner x2

No. 2 Pozi drive screwdriver

Small slotted screwdriver

External Circlip pliers 3-10mm

Long nose pliers

Side snips

Power Drill

Drill Piece set up to 8.5mm

 

Equipment Required

 

Step Ladder

Marker Pen

Cloth

Lint Free Cloth

The correct documentation

 

Previous
Next